RHS 180×100×8 vs CF RHS 180×80×10
RHS 180×100×8 is an RHS Hot-finished section from the UK Blue Book (SCI P363); CF RHS 180×80×10 is the closest equivalent in the UK Blue Book (SCI P363). RHS 180×100×8 carries more bending: 239 cm³ of plastic modulus against 234 cm³, 2.1% more. RHS 180×100×8 is the lighter of the two at 32.6 kg/m against 35 kg/m, a saving of 6.9% on steel weight. Both are about 180 mm deep, so either fits the same construction zone.
| Property | RHS 180×100×8 RHS Hot-finished | CF RHS 180×80×10 RHS Cold-formed | Difference |
|---|---|---|---|
| Mass | 32.6 kg/m | 35 kg/m | -6.9% |
| Depth | 180 mm | 180 mm | same |
| Width | 100 mm | 80 mm | +25.0% |
| Web thickness | 0 mm | 0 mm | same |
| Flange thickness | 0 mm | 0 mm | same |
| Area | 41.6 cm² | 44.6 cm² | -6.7% |
| Second moment, major (Iy) | 1,710 cm⁴ | 1,570 cm⁴ | +8.9% |
| Plastic modulus, major (Wpl,y) | 239 cm³ | 234 cm³ | +2.1% |
| Elastic modulus, major (Wel,y) | 190 cm³ | 174 cm³ | +9.2% |
| Second moment, minor (Iz) | 671 cm⁴ | 429 cm⁴ | +56.4% |
| Plastic modulus, minor (Wpl,z) | 157 cm³ | 131 cm³ | +19.8% |
| Radius of gyration, minor (iz) | 4.02 cm | 3.1 cm | +29.7% |
| Torsion constant (It) | 1,560 cm⁴ | 1,210 cm⁴ | +28.9% |
RHS 180×100×8 to BS EN 10210-2:2006; CF RHS 180×80×10 to BS EN 10219-2:2006. Difference is expressed relative to CF RHS 180×80×10.
How to choose between them
On stiffness, RHS 180×100×8 has the larger second moment of area: 1,710 cm⁴ against 1,570 cm⁴, a difference of 8.9%. This matters more often than the strength comparison, because on normal floor spans deflection rather than bending capacity sets the beam size - so if the two are close on modulus but apart on inertia, the stiffer one is usually the better answer even when it is not the stronger one.
Measured as bending capacity per kilogram of steel, RHS 180×100×8 is the more efficient section: 7.3 against 6.7 cm³ per kg/m, 9.7% better. Over a floor of repeated beams that difference is real tonnage, though it is often outweighed by whichever section the fabricator can actually source.
The two diverge much more about the minor axis: RHS 180×100×8 has 157 cm³ of minor-axis plastic modulus against 131 cm³, 19.8% more. If the member sees any minor-axis bending, or if it is unrestrained over a long length and lateral-torsional buckling governs, that gap decides the comparison even though the major-axis numbers looked equivalent.
In short, RHS 180×100×8 is the stronger section and RHS 180×100×8 is the lighter one; where those are the same section, it is the clear choice, and where they are not, decide on whether your design is governed by capacity or by tonnage.