Tee 178×203×43 vs WT 8X28.5
Tee 178×203×43 is an Tees (from UB) section from the UK Blue Book (SCI P363); WT 8X28.5 is the closest equivalent in the American AISC Shapes Database. They are close to interchangeable in bending: 226 cm³ against 226.14 cm³ of plastic modulus, a difference of 0.1%. They weigh essentially the same, 42.6 kg/m and 42.4 kg/m. Both are about 209 mm deep, so either fits the same construction zone.
| Property | Tee 178×203×43 Tees (from UB) | WT 8X28.5 WT | Difference |
|---|---|---|---|
| Mass | 42.6 kg/m | 42.4 kg/m | +0.5% |
| Depth | 208.6 mm | 208.8 mm | -0.1% |
| Width | 181.9 mm | 180.8 mm | +0.6% |
| Web thickness | 10.9 mm | 10.9 mm | same |
| Flange thickness | 18.2 mm | 18.2 mm | same |
| Area | 54.3 cm² | 54.1 cm² | +0.4% |
| Second moment, major (Iy) | 2,030 cm⁴ | 2,027 cm⁴ | +0.1% |
| Plastic modulus, major (Wpl,y) | 226 cm³ | 226.14 cm³ | -0.1% |
| Elastic modulus, major (Wel,y) | 127 cm³ | 127.33 cm³ | -0.3% |
| Second moment, minor (Iz) | 915 cm⁴ | 899.1 cm⁴ | +1.8% |
| Plastic modulus, minor (Wpl,z) | 157 cm³ | 154.37 cm³ | +1.7% |
| Radius of gyration, minor (iz) | 4.11 cm | 4.06 cm | +1.2% |
| Torsion constant (It) | 46.3 cm⁴ | 45.79 cm⁴ | +1.1% |
Tee 178×203×43 to BS EN 10365:2017; WT 8X28.5 to AISC Shapes Database v16.0. Difference is expressed relative to WT 8X28.5.
How to choose between them
On stiffness, Tee 178×203×43 has the larger second moment of area: 2,030 cm⁴ against 2,027 cm⁴, a difference of 0.1%. This matters more often than the strength comparison, because on normal floor spans deflection rather than bending capacity sets the beam size - so if the two are close on modulus but apart on inertia, the stiffer one is usually the better answer even when it is not the stronger one.
Measured as bending capacity per kilogram, the two are equally efficient (5.3 against 5.3 cm³ per kg/m), so on a pure steel-tonnage basis there is nothing to choose between them. The decision comes down to availability, connection detailing and what the rest of the frame uses.
These come from different catalogues, so treat the swap as a design change rather than a like-for-like substitution. Tees (from UB) sections are specified to BS EN 10365:2017 and WT to AISC Shapes Database v16.0; the steel grades, tolerances and available lengths differ, connection details and bolt gauges are set out differently, and the two are rarely both stocked in the same market. Check availability before changing a section on a drawing to save a marginal amount of weight.
In short, these two are genuine equivalents. Pick whichever your supplier stocks and the rest of the frame already uses.