The EA 130×130×15 is a steel section with a mass of 28.8 kg/m, an overall depth of 130 mm and width of 130 mm. It has a cross-sectional area of 37.1 cm², a second moment of area Iᵧ of 578 cm⁴, an elastic modulus Wₑₗ,ᵧ of 62.6 cm³, tabulated by CivilAxis from EN 10056 · Continental Steel.
Mass
28.8 kg/m
Depth
130 mm
Width
130 mm
Area
37.1 cm²
Ask about capacity, buckling or detailing for EA 130×130×15.
Dimension symbols for Equal Angle sections. Not to scale.
EA 130×130×15 section properties to EN 10056 · Continental Steel.
Geometry
Depth of section
h
130
Width of section
b
130
Web thickness
tw
15
Flange thickness
tf
15
Root fillet radius
r
14
Toe radius
r2
4.8
Mass and area
Mass per metre
mass
28.8
Cross-sectional area
A
37.1
Bending about the major axis (y-y)
Area moment of inertia about y-axis
Iy
578
Elastic section modulus about y-axis
Wel,y
62.6
Radius of gyration about y-axis
iy
3.95
Bending about the minor axis (z-z)
Area moment of inertia about z-axis
Iz
578
Elastic section modulus about z-axis
Wel,z
62.6
Radius of gyration about z-axis
iz
3.95
Principal axes
Area moment of inertia about u-u (major principal) axis
Iu
916
Area moment of inertia about v-v (minor principal) axis
Iv
240
Radius of gyration about u-u axis
iu
4.97
Radius of gyration about v-v axis
iv
2.54
Elastic section modulus about u-u axis
Wel,u
62.6
Elastic section modulus about v-v axis
Wel,v
62.6
Detailing dimensions
Centroid distance from back of leg (y)
cy
3.77
Centroid distance from back of leg (z)
cz
3.77
Common questions about EA 130×130×15
EA 130×130×15 has a mass of 28.8 kg/m, tabulated to EN 10056. A 12 m length therefore weighs about 346 kg, which is the figure to use for a steel take-off or when checking a lift.
EA 130×130×15 has a depth of 130 mm, a width of 130 mm, a web thickness of 15 mm, a flange thickness of 15 mm, with a cross-sectional area of 37.1 cm². These are the nominal dimensions from EN 10056; rolling tolerances apply to the delivered section.
The elastic section modulus about the major axis, Wel,y, is 62.6 cm³. Angles are tabulated about their principal (u-u and v-v) axes rather than a plastic major-axis modulus, so the elastic value is the one to design from unless you are working from the principal-axis properties directly.
The second moment of area about the major axis, Iy, is 578 cm⁴, and about the minor axis Iz is 578 cm⁴. Iy is the value deflection depends on - for a simply supported beam under a uniform load, the midspan deflection is 5wL⁴/384EIy - so on spans where a deflection limit governs rather than strength, this is the number that decides the section.
iy is 3.95 cm about the major axis and iz is 3.95 cm about the minor axis. Column buckling is governed by the SMALLER value: the slenderness is lambda = L_cr / i, so with iz = 3.95 cm a 0.4 m effective length already gives lambda = 100. Minor-axis buckling almost always controls unless the weak axis is restrained.
