SHS 150×150×8.8 vs SHS 150×150×9
SHS 150×150×8.8 is an SHS Hot-finished section from the UK Blue Book (SCI P363); SHS 150×150×9 is the closest equivalent in the European (Continental) range. SHS 150×150×8.8 carries more bending: 257 cm³ of plastic modulus against 248 cm³, 3.6% more. SHS 150×150×8.8 is the lighter of the two at 38.4 kg/m against 40.52 kg/m, a saving of 5.2% on steel weight. Both are about 150 mm deep, so either fits the same construction zone.
| Property | SHS 150×150×8.8 SHS Hot-finished | SHS 150×150×9 SHS Cold-formed | Difference |
|---|---|---|---|
| Mass | 38.4 kg/m | 40.5 kg/m | -5.2% |
| Depth | 150 mm | 150 mm | same |
| Width | 150 mm | 150 mm | same |
| Web thickness | 0 mm | 0 mm | same |
| Flange thickness | 0 mm | 0 mm | same |
| Area | 48.9 cm² | 48 cm² | +1.9% |
| Second moment, major (Iy) | 1,610 cm⁴ | 1,537 cm⁴ | +4.7% |
| Plastic modulus, major (Wpl,y) | 257 cm³ | 248 cm³ | +3.6% |
| Elastic modulus, major (Wel,y) | 214 cm³ | 205 cm³ | +4.4% |
| Second moment, minor (Iz) | 1,610 cm⁴ | 1,537 cm⁴ | +4.7% |
| Plastic modulus, minor (Wpl,z) | 257 cm³ | 248 cm³ | +3.6% |
| Radius of gyration, minor (iz) | 5.74 cm | 5.66 cm | +1.4% |
| Torsion constant (It) | 2,550 cm⁴ | 2,608 cm⁴ | -2.2% |
SHS 150×150×8.8 to BS EN 10210-2:2006; SHS 150×150×9 to EN 10219 · Continental Steel. Difference is expressed relative to SHS 150×150×9.
How to choose between them
On stiffness, SHS 150×150×8.8 has the larger second moment of area: 1,610 cm⁴ against 1,537 cm⁴, a difference of 4.7%. This matters more often than the strength comparison, because on normal floor spans deflection rather than bending capacity sets the beam size - so if the two are close on modulus but apart on inertia, the stiffer one is usually the better answer even when it is not the stronger one.
Measured as bending capacity per kilogram of steel, SHS 150×150×8.8 is the more efficient section: 6.7 against 6.1 cm³ per kg/m, 9.4% better. Over a floor of repeated beams that difference is real tonnage, though it is often outweighed by whichever section the fabricator can actually source.
These come from different catalogues, so treat the swap as a design change rather than a like-for-like substitution. SHS Hot-finished sections are specified to BS EN 10210-2:2006 and SHS Cold-formed to EN 10219 · Continental Steel; the steel grades, tolerances and available lengths differ, connection details and bolt gauges are set out differently, and the two are rarely both stocked in the same market. Check availability before changing a section on a drawing to save 5.2% weight.
In short, SHS 150×150×8.8 is the stronger section and SHS 150×150×8.8 is the lighter one; where those are the same section, it is the clear choice, and where they are not, decide on whether your design is governed by capacity or by tonnage.