CivilAxisCivilAxis
☕ Support🌐 Community

HE 140 A - Section Properties

The HE 140 A is a European wide-flange beam (HE) with a mass of 24.7 kg/m, an overall depth of 133 mm and width of 140 mm. It has a cross-sectional area of 31.4 cm², a second moment of area Iᵧ of 1030 cm⁴, a plastic modulus Wₚₗ,ᵧ of 174 cm³, tabulated by CivilAxis from EN 10365 · Continental Steel.

Mass
24.7 kg/m
Depth
133 mm
Width
140 mm
Area
31.4 cm²
Ask about capacity, buckling or detailing for HE 140 A.
🔍 Open the full Steel Catalogue📖 Design theory📐 Worked example
or pick a unit on any row
HE section profile showing the dimension symbols used for HE 140 A

Dimension symbols for HE sections. Not to scale.

HE 140 A section properties to EN 10365 · Continental Steel.

Geometry

Depth of sectionh133
Width of sectionb140
Web thicknesstw5.5
Flange thicknesstf8.5
Root fillet radiusr12
Depth between filletsd92

Mass and area

Mass per metremass24.7
Cross-sectional areaA31.4

Bending about the major axis (y-y)

Area moment of inertia about y-axisIy1030
Elastic section modulus about y-axisWel,y155
Plastic section modulus about y-axisWpl,y174
Radius of gyration about y-axisiy5.73

Bending about the minor axis (z-z)

Area moment of inertia about z-axisIz389
Elastic section modulus about z-axisWel,z56
Plastic section modulus about z-axisWpl,z84.8
Radius of gyration about z-axisiz3.52

Torsion and warping

Torsion constant (St Venant)It8.1
Warping constantIw0.0151

Classification and stability

Flange local-buckling ratiocf/tf6.5
Web local-buckling ratiocw/tw16.7
Buckling parameteru5.175
Torsional indexX13.9

Detailing dimensions

End clearanceC5
Notch dimension NN78
Notch dimension nn22

Surface area

Surface area per metreSA/m0.794

Is HE 140 A strong enough?

Simply supported beam, uniform load, major-axis bending - to EN 1993-1-1.

Passes - 61% utilised, deflection governs
Bending34%
21.1 / 61.8 kNm
Shear16%
33.8 / 207.2 kN
Deflection61%
4.2 / 6.9 mm

Class 1 section. ULS uses γQ = 1.5 on the load you enter; deflection uses the unfactored load against L/360. Lateral-torsional buckling is not included - the compression flange is assumed restrained.

Common questions about HE 140 A

HE 140 A has a mass of 24.7 kg/m, tabulated to EN 10365. A 12 m length therefore weighs about 296 kg, which is the figure to use for a steel take-off or when checking a lift.

HE 140 A has a depth of 133 mm, a width of 140 mm, a web thickness of 5.5 mm, a flange thickness of 8.5 mm, with a cross-sectional area of 31.4 cm². These are the nominal dimensions from EN 10365; rolling tolerances apply to the delivered section.

The plastic section modulus about the major axis, Wpl,y, is 174 cm³, and the elastic modulus Wel,y is 155 cm³. Wpl,y is what sets the moment capacity of a Class 1 or 2 section: M_pl,Rd = Wpl,y x f_y / gamma_M0, so at S355 with gamma_M0 = 1.0 this section reaches about 62 kNm before any stability check.

The second moment of area about the major axis, Iy, is 1,030 cm⁴, and about the minor axis Iz is 389 cm⁴. Iy is the value deflection depends on - for a simply supported beam under a uniform load, the midspan deflection is 5wL⁴/384EIy - so on spans where a deflection limit governs rather than strength, this is the number that decides the section.

Its local-buckling ratios are cf/tf = 6.5 for the flange and cw/tw = 16.7 for the web. EN 1993-1-1 Table 5.2 compares these against limits scaled by epsilon = sqrt(235/f_y), so the class depends on the steel grade as well as the geometry - the same section can be Class 1 in S275 and Class 3 in S355. Use the Capacity tab on this page for the classification at a specific grade.

iy is 5.73 cm about the major axis and iz is 3.52 cm about the minor axis. Column buckling is governed by the SMALLER value: the slenderness is lambda = L_cr / i, so with iz = 3.52 cm a 0.4 m effective length already gives lambda = 100. Minor-axis buckling almost always controls unless the weak axis is restrained.

The St Venant torsion constant It is 8.1 cm⁴, and the warping constant Iw is 0.0151 dm⁶. Open sections carry torsion mainly by warping rather than uniform torsion, which is why Iw appears in the lateral-torsional buckling resistance - both values feed M_b,Rd.

Related HE sizes

HE 120 BHE 120 CHE 120 MHE 140 AAHE 140 BHE 140 CHE 140 MHE 160 AA

Learn more

📘 How to read a steel section table (UB, UC, IPE, HE)📘 Section modulus explained: elastic (Wel) vs plastic (Wpl)📘 IPE vs HE (HEA/HEB): choosing a European steel beam
All HE sizes
Wide-Flange Beams (HEA/HEB/HEM)
Full steel section tables
Every UB, UC, hollow, channel & angle section
Open the interactive tool
Search, compare & run EC3 capacity checks
Rate this
No ratings yet
Sign in to join the discussion.
Loading…