Circular Hollow Sections (Cold-formed) (CHS) - Section Properties Table

What is in the CHS table

This page lists every Circular Hollow Sections - Cold-formed (BS EN 10219) size to BS EN 10219-2:2006, with the full set of section properties for each one. The table is sortable on any column and searchable by designation, and each size links to its own page with the complete property set, a worked capacity check and dimensions for detailing.

Sizes in this table

106

Mass range (kg/m)

2.3 to 194.0 - from CF CHS 33.7×3 up to CF CHS 508×16

Depth range (mm)

33.7 to 508.0

Major-axis stiffness, I (cm⁴)

3.44 to 74,900 - a factor of 21,773 across the range

Published to

BS EN 10219-2:2006

The spread is worth noticing: the heaviest CHS weighs 85.5x the lightest but carries roughly 21,773x the major-axis stiffness. Bending stiffness grows far faster than weight, which is the whole reason the range is shaped this way - going deeper buys stiffness much more cheaply than going heavier.

How to read a CHS designation

A CHS is called out as outside diameter × wall thickness in millimetres - CF CHS 244.5×6.3. Both figures are the real outside dimensions; nothing in the name refers to the bore.

That matters when you substitute a size: increasing the wall thickness of a CHS raises area and capacity without changing the connection geometry or the cladding line, which is usually why the range is built that way.

What each column in the table means

The table above publishes 11 properties for every CHS Cold-formed size. These are the ones that decide a design:

Mass per metre

Self-weight of the section, and the basis on which steel is bought - so it is the first cost signal when comparing two sections that both pass.

Cross-sectional area, A

Governs axial capacity and, with mass, tells you how efficiently the shape uses its steel.

Second moment of area, I (major axis)

Resistance to bending about the strong axis. It is what deflection is proportional to, so a serviceability check is driven by this number rather than by strength.

Elastic section modulus, Wel

Moment capacity while the extreme fibre stays elastic - the value to use for a Class 3 section, and for any check where yielding is not permitted.

Plastic section modulus, Wpl

Moment capacity once the whole section has yielded - the value used for Class 1 and 2 sections, and typically 10-20% above the elastic modulus.

Radius of gyration, i

The slenderness term: effective length divided by i gives the slenderness that drives buckling. The minor-axis value normally governs a column.

Torsion constant, J

St Venant torsional stiffness. Closed shapes carry torsion through a shear flow around the perimeter and have a J orders of magnitude above an open shape of the same weight.

Torsional section modulus, Wt

Converts an applied torque directly into a shear stress in the wall of a hollow section.

Surface area per metre

Drives the cost of painting, galvanising and fire protection - often the deciding factor between two sections of similar capacity.

Every one of these is a property of the shape alone. None of them depends on the steel grade - grade enters only when a property is multiplied by a design strength to give a capacity, which is what the Capacity tab above does.

Choosing a CHS size

Which property governs depends on what is being checked, and it is rarely the one people reach for first:

Bending strength

Compare plastic modulus Wpl for Class 1 and 2 sections, elastic Wel for Class 3. Depth buys this cheaply.

Deflection

Compare second moment of area I. A section that passes strength can still fail serviceability, and this is usually the check that decides the size.

Compression

Compare the MINOR-axis radius of gyration. A deep section with a narrow flange is efficient in bending and poor as a column.

Torsion

Compare J. If the load is genuinely torsional, a closed section beats an open one so decisively that the comparison is rarely close.

Cost

Compare mass per metre first, then surface area per metre - protective treatment is charged by area, not weight.

Elastic section modulus

$W_{el} = \frac{I}{c}$

Radius of gyration

$i = \sqrt{\frac{I}{A}}$

Slenderness

$\lambda = \frac{L_{cr}}{i}$

Open the Capacity tab above with a size selected to run these as a full EC3 check rather than comparing the raw properties by eye.

Common questions about CHS sections